Instructions for installing MET/CAL V7.20 SP1:

(1) You MUST start with a valid installation of MET/CAL V7.20 or later.

    MET/CAL V7.20 SP1 will not operate correctly if installed on a V7.11 or
    earlier MET/CAL system.

(2) To begin, you must first successfully download, or otherwise
    obtain, the V7.20 SP1 zip archive.

(3) You must understand how to extract zip files from the archive.

    The process of installing the V7.20 SP1 involves replacing selected
    files of your existing MET/CAL installation with files extracted from
    the zip archive.

    There is no formal install program for V7.20 SP1.

    Before proceeding with the following steps, extract all files from
    the V7.20 SP1 zip archive and store them in a temporary directory on
    your system.

    Then, in subsequent steps, described below, copy the files from the
    temporary directory to the proper MET/CAL directory.

    When all steps below have been completed, you can remove the temporary
    directory and the files it contains.

(4) Before replacing any of your existing files with files from
    the V7.20 SP1 zip archive you must:

	(a) Make sure none of the MET/CAL applications are running.
	    I.e., close the Editor, Run Time, and MET/TRACK
	    applications as needed.

	(b) It's not mandatory, but would be wise, to make back up
	    copies of your existing versions of the files to be replaced.

(5) Executables and Libraries:

	Replace your existing copies of all files in the archive
	with extensions ".exe" or ".dll".  These files are all
	located in the same place.

	On a client-server installation, these files are on the server.
	You have to know where they are, based on where they were placed
	when the MET/CAL Install Program was executed to install V7.20.

	On a stand-alone workstation, these files are in the "metcal"
	directory.  Again, you have to know or figure out where this is.
	The directory name and location are user-selectable when the MET/CAL
	Install Program is executed, and are not necessarily the same on
	every system.

(6) "mctext.mdb"

	This file is handled differently from the other files in that it may
	have to be placed in two different locations.  On a client-server
	installation, place a copy of the updated "mctext.mdb" (extracted
	from the zip archive) on the server in the same directory with the
	MET/CAL executables and DLLs.

	Then, on all systems (both client-server and standalone), you must also
	place a copy of this file on each MET/CAL workstation in the location
	indicated by the "mdb" parameter in the MET/CAL initialization file.

	In order to perform this step you must be able to find and view the
	MET/CAL initialization file.  The name of the file is "metcal.ini".
	The file is located in the windows directory on each MET/CAL PC.
	You can use various applications to view the file.  Notepad and
	Wordpad are two such applications.  To find the "mdb" parameter
	search for the string "mdb".  When you find a line like:

		mdb = <path>

	remember, or write down, the specified path.  That path is the place
	where you must place a copy of "mctext.mdb".

	An example of an "mdb" specification in the initialization file is:

		mdb = c:\station\metcal

	However, on your system the parameter value may be different from
	"c:\metcal".  It depends on your particular MET/CAL installation.

(7) Help Files

	Copy all files in the archive with the extension ".hlp" to your
	MET/CAL help directory.

	The name of the MET/CAL help directory is specified by the "helpdir"
	parameter in the MET/CAL initialization file.

	An example of a "helpdir" specification in the initialization file is:

		helpdir = c:\metcal\help

	However, on your system the parameter value may be different from
	"c:\metcal\help".  It depends on your particular MET/CAL installation.

	Refer to step (6) above for an explanation of how to search the
	initialization file ("metcal.ini").

	The service pack includes copies of all help files that have been
	created or updated since the V7.20 release.  It does not include
	help files that haven't changes since the V7.20 release.

(8) Accuracy Files

	Copy all files in the archive with the extension ".acc" or ".1yr"
	to your MET/CAL accuracy directory.

	For some of the accuracy files in the archive, you will not be
	replacing an existing file.  I.e., the file in the zip archive is
	the initial version of the file, and should simply be copied into
	the accuracy directory.

	The name of the MET/CAL accuracy directory is specified by the
	"accdir" parameter in the MET/CAL initialization file.

	An example of an "accdir" specification in the initialization file is:

		accdir = c:\metcal\acc

	However, on your system the parameter value may be different from
	"c:\metcal\acc".  It depends on your particular MET/CAL installation.

	Refer to step (6) above for an explanation of how to search the
	initialization file ("metcal.ini").

	The service pack includes copies of all accuracy files that have
	been created or updated since the V7.20 release.  It does not include
	accuracy files that haven't changes since the V7.20 release.

(9) Flexible Standards Initialization File

	The service pack includes an updated copy of "user_config_instr.ini".
	This file includes remote programming information for instruments
	supported by procedure-based flexible standards.

	This file should be placed in the station directory.  The path to
	the station directory is specified in the MET/CAL initialization file.

	Refer to step (6) above for an explanation of how to search the
	initialization file ("metcal.ini").

(10) Documentation

	Copy the file "Guardbanding.pdf" from the archive to your
	"metcal/manuals" directory.  The "metcal/manuals" directory is
	located on the server where MET/CAL is installed.

	You may also wish to copy these instructions,
	"MC720SP1_Instructions.txt", and the MET/CAL V7.20 SP1 readme file,
	"readme720sp1.txt", to the "metcal/manuals" directory for future
	reference.

(11) Validate Changes

	After following all of the steps above exactly, you should be able
	to start the updated Run Time, Editor, and MET/TRACK executables.

	No error messages should be displayed when starting the applications.

	For both Run Time and Editor, go to the "About" window and confirm
	that the version string shown is "7.20x".

	For MET/TRACK, choose "Help", then "About MET/TRACK..." and confirm
	that the dialog displays "Build #: 444".

	If you do not see "7.20x" for Run Time and Editor, you have
	not successfully installed the new executables ("mcr32.exe" and
	"mce32.exe").  Similarly, if you do not see "Build #: 444" for
	MET/TRACK, you have not successfully installed the new MET/TRACK
	executable ("mettrack.exe").  The most likely cause of this is
	failure to copy the files to the proper location.

	To troubleshoot, go to "Fluke Metrology Software" in the Windows start
	menu, then right click, in turn, on "MET_CAL Editor", "MET_CAL Run
	Time", and "MET_TRACK", and choose "Properties".  For each application
	look at the value of "Target:" in the "Shortcut" tab and confirm
	that the specified location matches the directory where you placed
	copies of the updated executables from the V7.20 SP1 zip archive.
